【土木】鱼藏溪桥施工图设计

收藏

编号:20171225101655607    类型:共享资源    大小:5.79MB    格式:RAR    上传时间:2017-12-25
  
25
关 键 词:
土木 鱼藏溪桥 施工图 设计
资源目录:
(温馨提示:点“+”可展开查看一级资源目录。点“-”可关闭资源目录。)
跳过导航链接。
资源描述:

摘要:我国改革开放以来,路、桥建设得到了飞速的发展,对改善人民的生活环境,改

善投资环境,促进经济的腾飞,起到了关键性的作用。桥梁工程在工程规模上约占道路

总造价的 10%—20%,它同时也是保证全线通车的咽喉,特别在战时,即便是高技术战

争,桥梁工程仍具有非常重要的地位,尤其是安全性至关重要,这就需要对桥梁进行计

算。本文就一座预应力混凝土连续刚构桥为设计目的,从而探讨桥梁设计方面的一些知

识。

根据对鱼藏溪桥址处的具体情况,并结合设计要求,拟定出三个比选方案,分别是预应

力混凝土变截面连续梁桥、预应力混凝土连续刚构桥及等截面连续梁桥。根据安全、适

用、经济、美观的原则确定预应力混凝土连续刚构桥为推荐方案,桥梁总长 250m,主

梁采用单箱双室箱形截面。使用 midas 程序进行结构计算。施工方法主要为满堂支架施

工法、悬臂浇筑法。

主要计算过程包括:计算恒载内力、活载内力,求得恒载内力、活载内力下结构的

弯矩图及剪力图,并按最不利情况进行加载,求得活载作用下内力包络图;按最不利组

合求得基础沉降引起的内力;施加温度荷载,求得温度荷载下内力;进行荷载组合,根

据各控制截面内力进行了估算和配筋计算,并对梁体进行具体的钢束布置。最后,对各

控制截面进行了强度、抗裂性、应力和变形验算。计算表明,各项验算符合要求,设计

方案合理

关键词:连续刚构桥 变截面 预应力 配筋

 鱼藏溪大桥设计

YuZangxi bridge construction project

Abstract:Since the reform and opening up of China,Road, bridge construction has been the

rapid development,To improve people's living environment, improve the investment

environment and promote economic take-off, played a key role. Bridge project on the scale of

the project about 10% -20% of the total cost of the road. It is also to ensure that the full

opening of the throat, especially in wartime, even the high-tech war, the bridge project still

has a very important position.Bridge is the throat of the traffic. Therefore, it is important to

ensure the practicability of bridge, especially the security of bridge, which requires precise

calculation of bridge. In order to explore some related knowledge of the bridge design, the

thesis intends to design a prestressed concrete continuous beam bridge.

According to the specific circumstances of YuZangxi Bridge’s site, the thesis on the

basis of the design requirements, works out two alternatives, which are respectively a

prestressed concrete continuous girder bridge and a reinforced concrete continuous rigid

frame bridge. The principles of safe, applicable, economic and beautiful determine that the

prestressed concrete continuous girder bridge is the recommendation. With single cell and

single box sections, the length of the bridge is 250m. And the design uses midas program for

structural calculation. The main construction method is the full framing construction method

and the cantilever method.

The calculation process mainly includes calculating the internal force of dead load,

calculating live load internal force, calculating internal force of dead load, and figuring out

live load internal force which is obtained under the structure of the bending moment diagram

and shear diagram. The author gains internal force envelope diagram which is under the

action of live load by loading on the basis of the most unfavorable situation. And on the basis

of the most unfavorable combination, the author gains foundation settlement which is caused

by internal force. Internal force under the temperature load is gained by applying temperature

load. And Load combination works out according to each control cross section’s internal

force to do estimation and reinforcement calculation, and to allocate concrete steel for the

beam structure. Finally, the author carries out section strength, crack resistance, stress and

deformation calculations to each control cross.

 鱼藏溪大桥设计

In conclusion, calculation shows that the calculation accords with requirements and the design

scheme are reasonable.

Keywords: continuous rigid frame bridge; variable cross-section; prestressing force;

reinforcement

 鱼藏溪大桥设计

目录

1 设计概述.................................................................................................................................1

1.1 设计依据及基本设计要求..................................................................................................1

1.2 桥址区地形概况..................................................................................................................1

1.3 材料规格..............................................................................................................................2

1.4 设计计算依据......................................................................................................................4

1.5 桥梁方案比选......................................................................................................................4

2 上部结构尺寸拟定及内力计算............................................................................................9

2.1 桥梁跨径的拟定.................................................................................................................9

2.2 横桥向设计..........................................................................................................................9

2.3 顺桥向设计........................................................................................................................10

3 主桥内力计算.......................................................................................................................11

3.1 节段划分............................................................................................................................11

3.2 截面单元几何特性.........................................................................................................121

3.3 施工方法及施工阶段简介..............................................................................................144

4 主梁恒载内力计算...............................................................................................................16

4.1 一期恒载作用下主梁内力计算.....................................................................................16

4.2 二期恒载作用下主梁内力计算.......................................................................................19

4.3 移动荷载作用下主梁内力计算........................................................................................22

5 温度及支座沉降次内力的计算...........................................................................................26

5.1 温度次内力计算.............................................................................................................266

5.2 支座沉降引起的内力计算................................................................................................37

6 作用效应组合及内力包络图...............................................................................................43

6.1 作用效应组合的原理.......................................................................................................42

6.2 正常使用极限状态设计效应组合....................................................................................48

7 预应力钢束估算及布置......................................................................................................57

7.1 预应力钢束估算原理.......................................................................................................57

7.2 预应力筋估算结果...........................................................................................................57

7.3 预应力筋束的布置原则....................................................................................................63

8.预应力损失及有效预应力计算...........................................................................................64

 鱼藏溪大桥设计

8.1 控制应力及相关参数........................................................................................................64

8.2 摩阻损失

 l1

的计算 .........................................................................................................65

8.4 混凝土的弹性压缩损失

 l4

的计算.................................................................................66

8.5 预应力损失及有效预应力计算结果................................................................................67

9 主梁次内力计算及内力组合..............................................................................................68

9.1 收缩徐变效应....................................................................................................................68

9.2 内力组合............................................................................................................................68

10 持久状况截面承载能力极限状态计算.............................................................................70

10.1 正截面抗弯承载力验算..................................................................................................70

10.2 斜截面抗剪强度验算......................................................................................................72

11 持久状况正常使用极限状态验算.....................................................................................73

11.1 结构正截面抗裂验算......................................................................................................73

11.2 斜截面抗裂验算..............................................................................................................74

11.3 正截面混凝土受压区法向压应力验算..........................................................................76

11.4 正截面受拉区预应力钢束中的拉应力验算..................................................................77

11.5 斜截面混凝土的主压应力验算......................................................................................84

11.6 挠度验算..........................................................................................................................85

12 短暂状况构件应力验算.....................................................................................................86

12.1 施工阶段法向压应力验算..............................................................................................86

12.2 预拱度设置.....................................................................................................................86

设计总结..................................................................................................................................88

主要参考文献与外文翻译文件..............................................................................................89

致谢..........................................................................................................................................90

展开阅读全文
  大分享文库-在线教育资源分享平台 所有资源均是用户自行上传分享,仅供网友学习交流,未经上传用户书面授权,请勿作他用。
0条评论

还可以输入200字符

暂无评论,赶快抢占沙发吧。

关于本文
本文标题:【土木】鱼藏溪桥施工图设计
链接地址:http://www.west960.com/p-257962.html
关于我们 - 网站声明 - 网站地图 - 资源地图 - 友情链接 - 网站客服客服 - 联系我们

copyright@ 2008-2018 大分享文库网 版权所有
经营许可证编号:豫ICP备11013292号-2

客服QQ:1965775022

收起
展开